Products & Solutions
IOT & Data Analytics
Partnerships
Mobiliz
Products & Solutions
Vehicle Tracking
Asset Tracking
Motorcycling Tracking
Mobile DVR & Camera Tracking
Special Solutions
Sectoral Solutions
Calculate how much you will save with Mobiliz, Click to start!
Advanced Package DT430
It is a package that allows a great number of sensors and external unit connections in addition to the Battery Standard Package.
Usage Area
It is the package suggested for the situations requiring a large number of different sensor connections other than the basic tracking features in terms of application.
Accessories
The Emergency Call Button can be used for sending an emergency call message to the centre, in cases of a malfunction, an accident or cases where it is necessary to take security precautions in the vehicle. The vehicle is taken under monitor by the centre. In Economics Package, the Emergency Call Button can not be used with Tank, Door Cover, Manhole Cover and Damper Sensors at the same time.
Depo / Kapı Sensörü, araçların kapı, yakıt deposu kapağı vb. kapaklarının açık veya kapalı olması durumları ile ilgili bilgi sağlayan bir aksesuardır. Kontrolsüz yakıt alınması, yakıt çalınması riskleri ve güvenlik açısından önem teşkil eden durumlarda kullanılabilir.
The Immobilizer Interface is an accessory which is used for the cases when the car is stolen or when it is necessary to stop the car for safety purposes. If the vehicle is started when the vehicle’s engine is closed, the vehicle does not operate and there will be no impact while the vehicle is operating however, the vehicle will not restart after it has been stopped.
When the values of Over Speed Limit defined in the unit is exceeded, it is used to give an audio alarm in the vehicle at the beginning of idle running. It can also be activated/deactivated using the web page when desired.
The Manhole Cover Sensor is a metal accessory which is manufactured to resist the external factors. It can be used to follow the open/closed states of manhole covers of vehicles such as fuel tank etc. or the dumpers.
In order to prevent the vehicle from being monitored in private uses, the driver may prevent the generation of address information by activating this switch. Information such as the distance covered and the violation of the Over Speed Limit will continue to be generated.
It is the interface with CANBus technology that obtains critical information such as vehicle fuel consumption, tank fuel level, engine speed (up to 50 sensors can be reached) from the on-board computer and puts them into the service of user. Data can be obtained from approximately 600 different brands/models of passenger cars or heavy vehicles without depending on FMS standard. Check the brand model information via Mobiliz for the compatibility of the vehicle (s) in which you consider using CANBus Interface.
The Temperature Sensor is an accessory ensuring that the temperature information of the ambient, in which the product carried during the transportation of cold chain products, is monitored in an integrated manner with the vehicle tracking system and that a warning is sent to the relevant persons via SMS and e-mail, in case temperature limits pre-registered in the sytem are exceeded. Temperature data can be obtained from 2 different points of vehicles with large trailer parts. Measurement of 0.5° sensitivity between -50 ° C and + 85 ° C can be made via digital sensor.
The Driver ID Set is an accessory which can be used to determine the driver using the vehicle on the basis of date and time and to ensure that detailed driver-based reports on vehicle usage can be received. It is useful in companies where it is possible for the same driver to drive more than one vehicle. This product can be used in ways of different applications, depending on demand: 1- "Buzzer" Application: If the driver ID unit is not read after the vehicle is started, this gives high volume audio alarm upon request. "Audio Alarm Unit" is used as an addition for this application. 2- Application Where the Vehicle is not Started: With this application, the vehicle cannot be started without the driver ID unit is read. "Immobilizer Interface" is used as an addition for this application.
With the RFID Card Reader you can use the existing personnel cards of your company as driver ID. You can track when your vehicles are used and by which drivers. This product can be used in ways of different applications, depending on demand: 1- "Buzzer" Application: If the driver ID unit is not read after the vehicle is started, this gives high volume audio alarm upon request. "Audio Alarm Unit" is used as an addition for this application. 2- Application Where the Vehicle is not Started: With this application, the vehicle cannot be started without the driver ID unit is read. "Immobilizer Interface" is used as an addition for this application. Properties of the Cards: All cards operating at the 125 kHz radio communication frequency and compatible with this frequency can be read with the Proximity Card Reader. It can read the cards at ISO15693 Standard. All cards operating at the 13.56 MHz radio communication frequency and compatible with this frequency can be read with the Mifare Card Reader. It can read ISO14443, Mifare Classic 1K, 4K and Ultralight cards.
The fuel tank float can be used in vehicles supplying analog voltage. The fuel level can be tracked as a percentage.
The Hands-Free Audio Kit is an accessory that enables to make voice calls between the driver and the centre and to listen to the vehicle remotely when desired. In addition, in cases of emergency, it can be ensured that the vehicle to call the centre quietly and inside the vehicle can be listened.
Specifications
Network Specifications
GSM/SMS/GPRS
check_circle
GSM 900/1800/1900 MHz
900/1800/1900 MHz
Detection of the Roaming Operator
check_circle
Physical Dimensions
Physical Dimensions
80* 49 * 26 mm
Weight
71 gr
Connector
16 pin Molex, Car compatible
Storage Temperature/Operating Temperature
-40°C;+80° / -30°C; +80°C
Protocol
UDP Support
check_circle
TCP/IP Support
check_circle
SMS PDU
check_circle
Dynamic IP Support
check_circle
Antenna
GPS
check_circle
GSM
check_circle
Hardware
Telemetry
4 Digital + 1 Analog Input, 3 Digital Output
Serial Port
Included
Internal Battery
Li-Polimer 250mAh
Light Indicator
Remote Firmware Upgrade
check_circle
Message Memory (unit)
10000 (can be increased)
Telemetry Specifications
Digital Outputs
3
Digital Inputs
4 (1 contakt)
Analogue Inputs
2 configurable
GPS Receiver Specifications
Technology
u-blox All-in-One GPS Receiver
GPS Receiver Specifications
-162 dBm
Cold Startup Time
27 sec
Hot Startup Time
1.2 sec
Warm Startup Time
27 sec
Antenna
Included (external antenna ops.)
GPS Channel Number
GPS+GLONASS 56 Channel
Certificates
CE
check_circle
E-mark
check_circle
Which Device Should I Buy
Ekonomik
Standard
Gelişmiş
Easy to use
Quick access to summary information based on organization, fleet and group
Ability to monitor the vehicles on the map by filtering according to 6 different options
Vehicle-based adhoc query
Periodical monitoring according to time
Ability to get the density map of the vehicle or vehicles selected on the map at specific time intervals
Tracking by entered and exited zones
Tracking by control points
Tracking by violation values
Tracking feature on a map by vehicle, group, fleet and organization
Daily vehicle-based briefing
Daily vehicle-based detail information screens and animation feature
Ability to query vehicles passing through a certain point
Zoom-in, zoom-out features on the map, shifting of the map, focusing by the car
Address, speed, total daily route, message warning and violation warning and number of vehicles on the same screen
Easy user interface management
Ability to authorize the user for monitoring by user types
Driver identification and easy vehicle identification for drivers
Ability to receive reports about vehicle, driver, violation, overtime, area-route sensor, trailer, voyage, user and road computer (Note1)
Ability to receive automatic mailing by scheduling reports for the desired time
Ability to receive the reports in pdf, excel and CSV formats
Ability to receive the reports in 9 different languages
Ability to see detailed notifications based on violation schedules defined for vehicles
Access to educational videos of Expressive Web, Android and IOS applications
Determination of time frequency
Determination of distance frequency
Determination of turning angle
Determination of violation parameters
Time to commence work
Time to quit work
Speed limit
Instant idle time
Daily idle time
Instant stopped time
Daily stopped time
Daily movement time
Limiting the number of drives if drive id units are used
Sudden take-off/stop or accident reporting
No GSM connection alert
Motion alert when the ignition is off
Sudden fuel low alert
Motion without driver alert, if drive ID units are used
Ability to receive all violations via mail
GPS Antenna Breaking/Connection Status Information
Ability to program modular sensors (temperature, fuel level, humidity level) in vehicles
Ability to define periodical transactions (tax, maintenance, inspection ... etc.) of the vehicles and ability to receive alerts
Entered zone alert
Exited zone alert
Enter/exit alerts in control points
Vehicle-based reports
Violation Based Reports
Driver Based reports
Shift Reports
Area / route reports
Sensor reports
Trailer based reports
User reports
Ignition switch input
Emergency button
Door / cover / damper / mixer sensor
Fuel tank cover sensor
Temperature sensor
Driver ID set
Card reader
CANBus Accessory
Canbus and Card Reader accessory together
Immobilizer engine block
In-car audio alarm
Analogue fuel connection
Opportunity to Use Built-in Battery
Special case extra key
Tachograph data download
Targetmatic
My child is safe solution
My Passenger is Safe Camera Monitoring System Compatibility
Smart Bus Stop Tracking Software
Compatibility with Excavation Software
IPHONE / IPAD (iOS) Vehicle Tracking Application
ANDROID Vehicle Tracking Application
OGS / HGS pass feature
Tachograph integration
- Var
- Yok
- Opsiyonel Özellik
Similar Products